You can only fit a wood burner in your fireplace if it has a class 1 chimney. It is very important that your wood burner is connected to the correct size flue or flue liner – if it isnt, it will not only perform badly, but wont be safe either. Most stoves of up to 20kW need a minimum of a 6” flue diameter.

Can furnace and wood stove on same chimney?

NFPA 211 (Section 9.8) prohibits the interconnection of solid fuel-burning appliances into any chimney serving another appliance. No combination of fuel-gas, oil-fired, or additional wood, wood pellet, coal or corn stoves may be vented into the same chimney flue as a solid fuel-burning appliance.

Does a wood stove need a chimney?

When used properly, a wood-burning stove can be the main source of heat for a home. It will continue working even if the power goes out during a storm. Because a stove needs a way to vent the heat, smoke and gas that builds up when the wood is burned, a chimney is required for any wood stove installation.

Do you need planning permission for a wood burning stove chimney?

To get a wood burning stove installed in your home, the government states that you do not need to acquire planning permission from Building Control if these conditions are adhered to: The flue is situated at the rear or side of the building with a maximum clearance of 1m above the highest part of the roof.

Can you vent a furnace into a chimney?

Furnaces with an AFUE of 90% and greater use special venting material such as PVC or stainless steel. A 90% furnace should never dump flue gases into a chimney. Using an abandoned chimney as a chase for a metal venting system, such as “B” Vent, can be done.

How much does it cost to install a wood stove and chimney?

The average cost to install a wood stove is $1,200 to $4,500. A wood burning stove costs $400 to $3,500, while a wood stove insert runs $1,200 to $3,400. Wood stove installation costs $250 to $800 for labor, and installing a ventilation system or chimney costs $300 to $3,500.

Can you vent a 90 furnace through the chimney?

A 90% furnace should never dump flue gases into a chimney. The installation instructions of these furnaces must be followed precisely for safe installation and operation. These furnaces produce large quantities of condensate as part of their operation.

How do I know if my chimney needs a liner?

One of the most common signs that you need a chimney liner is when you notice that your chimney walls are deteriorating at a faster than normal pace. When your liner is not in proper working condition, the heat or condensation will damage your brick and mortar at a higher rate.

Does wood burning stove add value to house?

While many people choose a log burner to fulfil a dream of a cosy home, others are much more practical! Wood burners can add value to your house, too. In fact, we have done our research and have found most sources suggest your home value can increase by up to 5% by installing a log burner!

What is the average cost of installing a wood stove?

It typically costs about $3,000 to install a new wood stove. While prices can range from about $2,000 to $4,000, high-end projects can cost upward of $5,000. The total cost of your project will depend on the type and size of stove you purchase, the cost of ventilation parts and labor rates in your area.

What causes a chimney not to draw?

The main reasons why your wood stove does not draw can include: The stove or flue is too cold. The flue or chimney is dirty. The room or house is too airtight.

What is the 3 to 10 rule for chimneys?

This rule means that your chimneys shortest side needs to be at least 3 feet above the roof penetration, and its top has to be 2 feet higher than any part of the building thats within 10 feet.

Do I need permission to install a wood burner?

You do not technically require planning permission to install a wood burning stove, however since 2005 it has been a legal requirement to let your local authority building control department know of your intentions – no matter what type of heating appliance you are installing.

What is the 3 2 10 rule?

This rule means that your chimneys shortest side needs to be at least 3 feet above the roof penetration, and its top has to be 2 feet higher than any part of the building thats within 10 feet.